This machine is used for forming various shapes of rice candy,such as round type
belongs to the versatility of the production line,it can produce Cereal bar、crunchy candy、Nuts crisp,、sesame crisp and so on.
Standard machine specifications and technical parameter performance
Size (total size with the cooling belt)
Note: In the above table, main specifications and parameters are the enterprise standard model has. If you require other parameters and specifications, need to replace machine equipment in corresponding parts. Belong to the standard. If your machine is a standard configuration, the temporary not mentioned in the manual.
2、Installation and commissioning
Do not install the equipment in the following place, otherwise, it will affect the normal use of equipment.
When you put the equipment in the horizontal plane installation, should be sent to the product as the reference plane, make the equipment in horizontal plane, in order to level installation equipment, in reference to the plane (namely transfer product level surface) put a level. Most of the regulating equipment under the six adjustment screw, make the product transfer cost level plane. If there is a need and production line other machines or process combined. For example: make the equipment and the conveyor belt matching position, then decide how machine position, in order to avoid product transfer process not smooth.
②Not in the sunlight straight drying
If the equipment installation in direct sunlight or strong light place, photoelectric switch can damage.
③Temperature is unfavorable and exorbitant also should not be too low, the space can not be too narrow. This machine is adapt to the environment temperature at 0℃-45℃.
⑤Equipment should be put in vents
⑥Equipment is not suitable for in corrosive gas or dust site
This machine use the 380 v, frequency50 Hz ac, forbidden the machine connect to other do not meet above requirement of power supply. For the safety, connection there should be a complete electrical professionals.
②Turn on the power switch
Open the machine electric control panel of total switch power supply.
First turn on the power, do the following check：
①check working mesa, conveyor belt, sealing knife sit must not have the tools or any other sundry. Observe the machine without exception around.
② determine whether the switch with two close by induction, will the sheeter knife of induction plate moved to the corresponding close to switch, see close to switch to the rear of the indicator light is normal light, such as not bright, need to adjust the position.
③ensure that the minimum speed regulation knob speed position, check the machine is normal operation.
②Connect power,computer box appears boot screen, enter the password （PICTURE3） into interface（PICTURE4）
4、Adjustment and operation matters
①material length: it is to point to you by the production of products length. By clicking on the screen modification parameter options. Pop-up new interface, the input password, click on the material length numerical modified.
②the sliding coefficient: is fine-tuning product length error coefficient. By clicking on the sliding coefficient parameters can be modified.
③production: you are in the production of products of the count.
Yield reset: is your products to new count.
（2）adjust conveyor belt
①active roller adjusted: moving front adjustment is adjusted active roller conveyor belt, with two sides to the conveyor belt conveyor belt roller of the two edge distance equal basis. (the side a side, and the other side says said b side). If the machine during the work and the distance of a greater or less than b slowly, it should be a narrow edge conveyor belt roller support plate and support the paddle distance behind or increase b side roller conveyor belt support plate and support the paddle distance behind. By adjusting the adjustment screw to front expand or contract conveyor belt roller support plate and support the paddle distance behind.
② the driven roller adjusted: after adjustment is to adjust the conveyor belt conveyor belt driven roller, also with two sides to the conveyor belt conveyor belt roller of the two edge distance equal basis. (the side a side, and the other side says said b side). If the machine during the work and the distance of a greater or less than b slowly, it should be adjusted to the rear of the adjusting screw (clockwise for tight, counterclockwise for loose).
（3）pressure roller adjusted
The height of the pressure roller according to the thickness of the products you need to adjust. Simply adjust pressure roller adjusted above the handwheel. (clockwise for tight, counterclockwise for loose).
Related Industry Knowledge
- How long should the reverse osmosis...
- New trends in the development of fo...
- The trend of the innovation of food...
- The wide application of food machin...
- Market change of baked food machine...
- What is the convenience of beverage...
- A course of installation and use of...
- Precautions for drilling machine op...
- Development direction of packaging ...
- How to improve the packaging effect...
- how to use hydroponic fodder machine
- Hydraulic rig maintenance hydraulic...
- Diesel gasoline hydraulic drilling ...
- Electric 180 Drilling Machine Instr...
- OR-500 BROAD BEAN PEELER Operation ...
- OR-320 High-Speed Pillow Automatic ...
- Advantages of our garlic peeling ma...
- user manual for the meatal detector
- Full automatic soybean milk instruc...
- How to sprout the garlic